# Question: How Deep Should I Bury A 10 Foot Post?

## How deep should an 8 foot post be in the ground?

3 feetIn general, holes should be at least 3 feet deep for posts that extend 8 feet or more above ground level..

## Should I use 4×4 or 6×6 fence posts?

Instead of 4×4 posts, go with 6×6 posts. The extra size makes a huge difference. It’s a smart place to invest a little extra in your fence, because if your posts distort after they have been set in the ground with concrete, they are extremely difficult to replace.

## What is a good distance between fence posts?

between six and eight feetTypically, fence posts are spaced between six and eight feet apart. The corner posts are set first. To align all of the posts in between, stretch a line from each corner post to work as your guide.

## How far apart should I put T posts?

You should space your posts 8-12 feet apart as a general rule, although 10-12 feet apart is sufficient for 5-6 wire barbed fence. Position each post with the anchor plate at the bottom and perpendicular to the fence line.

## How do you install a 6×6 fence post?

A 6×6 post requires a 10″-diameter hole. Shovel a 6″ layer of gravel into the hole to provide drainage. Now, put the strings back on the batterboards, but move them toward the outside of the layout by one-half the post thickness. Set each post in its hole, and move it until the outside edge lines up with the string.

## How much quikrete do I need for a post hole?

Remember, the depth of the post hole should be one-half of the above-ground post height. (Example: For a 6 feet above ground post, use a post with an overall height of 9 feet and place 3 feet in the ground). The calculator will indicate the number of 50 lb. bags of QUIKRETE® Fast-Setting Concrete you need.

## How deep should a 10 foot post be in the ground?

The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole.

## How far should concrete fence posts be in the ground?

Concrete fence posts must be fixed into the ground in the traditional way: by digging a hole. When concreting fence posts into the ground, the posts should be buried a minimum of 600mm deep. The recommended depth for a 1.80m or 6 foot high fence is 760mm or 2′ 6″.

## Can fence posts be 10 feet apart?

Typical spacing is right around 8 feet between each post however different circumstances may call for different measurements and it is not uncommon to have spacing between posts reach up to 10 feet. Once you have a rough idea of your post layout start by digging your first hole.

As chain link fence posts are smaller and sturdier than many other types, the holes should be smaller and can be farther apart. Follow the fence manufacturer’s instructions for spacing, which typically ranges from 4-10′ apart—spacing should not exceed 10′ on-center.

## How many bags of concrete do I need for a 4×4 post?

Mix two 50lb bags of concrete with water in a mixing tub or 5-gallon bucket. Add concrete into the hole and around the 4” x 4”. Depending on your climate, let concrete set up for 24 – 48 hours.

## How big of a hole do I need for a 6×6 post?

about 12 inches squareFor a 6×6 post, the diameter of the holes should be about 12 inches square. As a rule the width of your post hole should never be less than 10 inches. You want holes deep and wide enough to easily support a standard 4×4 post.

## Will wooden posts rot in concrete?

A: Actually, your point is well taken. Simply setting the posts in concrete does create a condition that will accelerate rot in the bottom of the posts. With pressure-treated posts, the rot will be slow. … Concrete should be poured around the post – no concrete under the post.

## What is the cheapest fence to build?

The Most Affordable Ways to Fence in a YardAhead, find the fence type that fits your needs and budget. … Treated pine (\$12 to \$19 per linear foot installed) … Chain link (\$10 to \$20 per linear foot) … Wrought iron (\$24 to \$32 per linear foot) … Barbed wire (\$1.50 to \$2 per linear foot) … Hog wire (\$3 to \$5 per linear foot) … Electric (\$1 to \$6 per linear foot)More items…

## What size posts do I need for a 6ft fence?

If you’re setting wooden or concrete posts in concrete you’ll need 8ft (2.4m) posts for a 6ft (1.828m) fence – i.e. your posts are 2ft (0.6m) longer than the fence height. Use 4in x 4in posts for fences of 5ft and over and 3in x 3in posts for anything under 5ft.